DIY Grand Cherokee ZJ

[υк ¢яєω]

a Cherokee Pickup ?

http://www.canadianjeepoffroad.com/foru ... p?t=146624

[alpha_Ω]

ok, not a ZJ, but a XJ

http://www.houston-imports.com/forums/s ... ffroad-rig

[υк ¢яєω]

same old story,

first, you have to be a "silver-digger",

when you check your status of your transmission.
(check, if you find metal parts in thr oil of your Auto-transmission)

second, check the rest of your car,

and then,

you can start, to build it up,

otherwise, you are running out of cash,
if you start with the wrong car.

everything,

like wrapping,
styling, pp.

its only for the right car.

a styling idea, (but not for a jeep - uuuuh )

phpBB [video]

[7/11]

hi uk,

after wrapping, there is the way of plasti dip or

phpBB [video]

Halo is a more expensive product which would be the reason for the price differnce.
Although the differnce is only about 7 per gallon.
Another thing is that, while coats are inportant, gallon count per car is what is required.
Halo efx is a more refined product. When sprayed properly, which should happen in a professional shop, it goes on with less texture and is less likely to lift.

[υк ¢яєω]

Plasti Dip is ok, if you do the inside work

ok,

this one is for the cars with headlights with plastic glass, not real glass,
but also with plastic glass for your instruments inside.

These will not stay clear forever, and will get scratches or become unclear.

Best way, protect them, like you do with your smartphone display, use an untint cover.

phpBB [video]

[υк ¢яєω]

interior warp design

https://www.youtube.com/watch?v=31suApP ... 8D_TQ019a1

sillver ?

emerald pearl metallic Avery wrapping film Rmwraps.com

only fridge wraps 555
https://www.rmwraps.com/mini-fridge-wraps-1/

[υк ¢яєω]

Grand Cherokee ZJ door panel removal

do the line between Panel and door,
move the lower part to direction to your bode position
and lift the upper clip to the direction of the window.

https://www.andysautosport.com/products ... 040-1.html
http://www.karosserieteileshop24.de/JEE ... 467_206.63

[υк ¢яєω]

this is a general DIY, for nearly any car

phpBB [video]

[υк ¢яєω]

How do i replace the starter on a 95 jeep grand cherokee v8
The main thing is to disconnect the negative battery cable before doing the work, and you will need to get the Jeep up onto some sturdy jack stands or ramps. It basically involves removing the large cable from the starter, the small wire from the starter, and the bolts that hold the starter to the bell housing. Here is the procedure for doing this, and I hope this information is helpful. Let me know if you need more assistance with this,

Chris.

5.2L AND 5.9L ENGINE
Disconnect and isolate the battery negative cable.
Raise and support the vehicle.
Remove the battery cable and wire harness connection from the starter solenoid Starter Wire Harness Remove/Install - Typical
Remove the lower starter mounting bolt and the exhaust brace Starter Remove/Install - 5.2L and 5.9L Engine
Remove the upper starter mounting nut, lock washer, and automatic transmission oil cooler line bracket.
Move the starter towards the front of the vehicle until the starter gear housing nose clears the bellhousing. Then tilt the starter nose downwards past the exhaust pipe.
Reverse the removal procedures to install. Tighten the starter hardware as follows:
Lower mounting bolt - 68 N·m (50 ft. lbs.)
Upper mounting nut - 68 N·m (50 ft. lbs.)
Battery cable terminal nut - 10 N·m (90 in. lbs.)
Solenoid wire harness terminal nut - 6 N·m (55 in. lbs.)

https://www.justanswer.com/jeep/2lx4r-r ... ee-v8.html

car is not starting,
full dashboardlights, no clicking during the start, just nothing,
problem with the Ignition Lock Switch

or the cabel from the Ignition Lock Switch to the left pin of the starter

just bridge the left pin with the battery, like in the following vdo

phpBB [video]

[υк ¢яєω]

phpBB [video]